Tom’s teenage dive into the convertible helped him develop his bodywork skills at that early age, along with the help of his father, Harold, while welding skills were honed because of shop class. After high school he embarked on his first station wagon project, a ’66 four-door Chevelle wagon that he started to convert into a two-door hardtop. Part of that build relied heavily on a wrecked ’98 Camaro for its drivetrain and braking. Tom managed to get as far as completing one side of the conversion when the ’72 Oldsmobile Vista Cruiser popped up on his horizon in 2014. “My brother, Anthony, found the wagon on Craigslist,” he explains. “He said it was cool and I should go and look at it and buy it because it was cheap.” It turned out that it was a local listing and it didn’t take him long to cut a deal on it—as a bonus many spare parts and a well-worn ’72 Oldsmobile Cutlass Holiday Coupe were included.

Originally sold new in Washington, at some point it migrated to Oregon, which is where the previous owner purchased it from back in 2009. Tom explains, “He found it online, so he flew out there and drove it back to Pennsylvania.” Years later, his decision to sell it came down to a lack of space and time to work on it.” He further explains, “The overall condition of the Vista was pretty good. He had taken out the carpets and the headliner to paint the floors with a rust preventative. It still had the original seats and door panels, and he had the rear doors, hood, roof, and the upper sections of the rear quarters repainted. The rest of the car still had its original Baroque Gold paint. The woodgrain was still original but it did have some rust along the bottom of the rear quarters.” The 350ci two-barrel Rocket V-8 mated to a TH375 was equally original and fully roadworthy. Overall, it was in decent shape given its age.

As he rolled into 2014, the Vista wagon became his daily driver–probably not what most would expect with such a vehicle. That didn’t mean that it would be left as-is. His first mission was to swap out the stock suspension and improve the braking. Making this easier came down to having a pile of parts that he amassed for the Chevelle wagon project. By the beginning of 2015 he had the stock frame bagged. Up front he installed Ridetech single-adjustable ShockWaves and upper and lower tubular control arms mounted on stock spindles, along with a 1-1/4-inch UMI sway bar. At the rear a UMI tubular four-link was added and their 1-inch sway bar, along with QA1 single-adjustable shocks and Slam Specialties airbags. At that point the ’bags were being activated by a pair of Air Lift ViAir 480C dual compressors. Toward the end of 2015 he spent a week swapping out the original brakes with the disc brake assemblies from the donor Camaro. The stock Olds discs were swapped up front, and at the back Tom replaced the original rear with a 10-bolt donor from a Chevelle that then received the rest of the Camaro disc brake hardware. At that point it went back on the road for some more daily driver duties.

It wasn’t until the middle of 2017 that the next chapter started to come together. On the agenda was an engine swap with the LS1 out of the Camaro, along with a refurbish and repaint of the frame, smoothing of the firewall, and an interior makeover. After the frame was separated from the body, the LS was given a complete refresh. The bottom end was left stock, while the top end received a set of fresh LS2 heads and a Comp Cams 54-000-11 custom ground camshaft, all capped off with a Sharp Customs 102mm black LS1/LS2 sheetmetal intake. Other components from the parts pile included a TSP billet serpentine assembly, Derale 4000 fan, and a frame-mounted Walbro 255 fuel pump. Ensuring this combination worked in its new home meant that an ECM manipulation was needed, so Tom reached out to the folks at Ron Francis Wiring for an LS ECM reprogram. The 4L60E from the Camaro also made the migration over, while the exhaust was fresh with a set of Speed Engineering stainless long-tube headers mated to 2-1/2-inch stainless pipes running back to a pair of MagnaFlow mufflers. The Camaro discs and rotors were also swapped with some new Wilwood hardware. At the front he installed their six-piston calipers and 14-inch rotors, and at the rear four-piston calipers and 13-inch rotors. As all that unfolded, the interior slowly came together. Red was the final choice, and the entire process spanned a number of months and was done piecemeal–literally. As each component was finished, Tom would go and pick it up at Mel’s Auto Upholstery in Manheim, Pennsylvania. At that point the wagon project was sidetracked. He purchased a partially restored ’68 W34 Olds Toronado that consumed all his time. The wagon was running by that point but didn’t have any fenders, interior, and bumpers, so it was parked. It wasn’t until the fall of 2019 that he was able to get it back on the road to test everything. As he started wrenching on it again, he swapped out the existing compressors and installed an AccuAir 5-gallon four-corner CVT as the backbone for the air-ride system.

A few months after it was debugged, he decided to take it to the next step. He notes, “I wanted to keep the exterior untouched but with a nice interior. The woodgrain had a nice patina but they cut into it when they sprayed the rear quarters and I realized that they weren’t savable.” At that point he decided to move ahead with the bodywork. Also, in full stride by that time was the COVID-19 pandemic, and as a schoolteacher with newly imposed lockdowns some extra time was made available to get the body done.

As he embarked on the final step, the body and frame were once again split. “The car wasn’t in too bad of shape because I had already done some of the metalwork, so it took me about four months to get it primered and wet sanded,” he explains. At that point it was sent off to his brother Anthony’s garage to lay down the 2019 PPG Corvette Arctic White basecoat/clearcoat. Once that was buttoned up, still left hanging was a viable replacement for the woodgrain panels. That solution came in the form of a wrap. Tom decided to ditch the woodgrain in place of a Black Metallic brushed metal vinyl wrap. With the interior partially done, he sent the wagon to Full Throttle Wraps in Oxford, Pennsylvania, to get it applied. The rest of the interior was the last hurdle, and in all that sea of red were some 21st century accoutrements like Dakota Digital VHX gauges, push button start with passive keyless entry, power windows, cruise control, four-way electric power mirrors, Vintage Air Gen IV, three-spoke Billet Specialties steering wheel with Twist Machine D9 paddle shifters. Those paddle shifters work with a modified ’13 Land Rover in-dash rotary shifter and PCS GSM push button shifter. As with the interior, the rolling stock was also upgraded with modern hardware in the form of Boss Motorsports Boss 338 wheels wrapped in Nitto tires. The front wheels measure 18×8 and the tires 245/40ZR18W, at the rear they measure 18×9.5 with 275/35ZR18W tires. The final detail was the addition of vulcanized redline sidewalls from the folks at Diamond Back Classic radials.

While this was a project that spanned a number of years, the last push to get the wagon done can easily be called a pandemic build. Overall Tom is quite satisfied with the outcome. The wagon made it out in the spring of 2021 to its first show and was very well received. When asked if there is anything that he would consider doing differently, he states, “I would have liked to put an LSA supercharger on it at some point, but now I’m leaning toward an eight-stack. There are some decent looking ones being made, so maybe within the next year.”