It should be noted that Chris and his staff are no strangers to building amazing-looking customs and other hot rods. Jack Walker, a close friend and hall of fame builder, once told Chris, “If you can walk from the back of the car to the front and nothing makes you stop and question it, then you got it right.”

Let’s “walk” around the Firebird Trans Am via our photos, noting what we think. What was once plastic (or fiberglass) flares were replaced with freshly minted sheetmetal by the RR&K staff that were welded to the fenders.

Remember this was the era of square/rectangular headlights. The Trans Am stocker lighting was replaced with modern halogen that are now encapsulated with LED halos for park and turn signal functions nestled within the custom aluminum grilles from Alumicraft. Remember those Firebird fender vents? They were retained but refined and fitted with a custom wire mesh like what we see in the reworked shaker hood scoop. The windshield and the surrounding area underwent significant mods while the A-pillar was reshaped and the bottom of the windshield was moved toward the hood, thus closing the gap normally occupied by the wipers. The front and rear glass are both Fessler flush-mounted DOT units.

Moving our eyesight downward we can see Chris had the rocker area lowered 1 inch, thus matching the factory pinch weld edge. Look closely and you will see a slight flare located at the rear of the front wheel opening. Where once the factory door handles could be found, now you will use Nissan GTP flush-mounted units with locks deleted. As in the front, the rear factory flares were replaced with custom sheetmetal versions welded to the body that were resized to handle the modern rubber and wheel combo.

More RR&K custom sheetmetal work includes the trunk spoiler typically found on Firebirds and Camaros of that era. When looking at the stock taillight housings they now encapsulate LED taillights with sequential brake and turn signal functions. The rear bumper cover was replaced with a new fiberglass version that features a reshaped appearance. From this point the rear quarter-panels were stretched to flow neatly into the rear bumper valance area. There are also Detroit Speed 2-inch widened wheeltubs. All this massaged sheetmetal was painted at RR&K in an Axalta Donnington Gray (a color found on a ’21 BMW) with Axalta clear 72500. The hood features the obligatory Firebird, this time hand painted by Jeremy Sanor in hand-turned silver leaf.

There is also sheetmetal handiwork to be seen underhood. There is a one-piece underhood panel shaped to work with the fender lines as well as conceal the radiator and core support area. The firewall was smoothed over while the cowl vent panel was deleted.

Since we are talking about what’s underhood, a Trans Am wouldn’t be worthy of its ’bird on the hood without a tuned-up, modern-day powerplant. A 6.0L iron block LS with a 0.020-inch overbore yields plenty of power. The decked and line-bored block along with balanced reciprocating components was handled by Bouchard Racing Engines. Accompanying the iron block are aluminum heads held in place by ARP head studs while a beefed-up hydraulic roller camshaft is used. The water pump comes from Edelbrock, a pair of SPAL electric fans, a PRC custom-built radiator, and a Billet Specialties Sport Trac serpentine belt system assists with the cooling and electrical chores. A Powermaster alternator, a factory starter, and an Optima RedTop battery supplies the spark. Resting between the aluminum heads is an Edelbrock Victor Jr. LS intake with a Holley Sniper. The ignition is a combination of Holley EFI and Edelbrock controller. Moving the spent gases out belongs to a pair of Hooker Blackheart LS headers with custom-made 3-inch stainless steel pipes, a pair of mufflers, and original factory Trans Am tips.

The V-8 backs up to a B&M 4L80E overdrive with converter that is operated through a TCI controller and a Shiftworks universal rod linkage kit. The power is then moved rearward through a Fast Shafts forged yoke/driveshaft ending at the Currie 9-inch rearend outfitted with 31-spline axles and 4.11 gears.

The chassis is based on a factory frame modified by RR&K to use Ridetech TruTurn IFS, coilover shocks, and a sway bar. Next up is a Borgeson steering box coupled to an ididit steering column. In back a Ridetech four-link is used along with more Ridetech coilovers. You will also find Detroit Speed subframe connectors and aluminum body mount bushings. As for braking there is plenty in the form of vented Wilwood 13-inch drilled-and-slotted front rotors coupled with six-piston Superlite calipers while in back four-piston Superlites are used. The system is pressed into service through modified factory pedals pushing a Wilwood 7/8-inch bore master cylinder. The wheels represent Chris’ interpretation of a snowflake style of one-off wheels from Mike Curtis of Curtis Speed Custom. The custom wheels measure 18×9 in front and 19×12 in the rear, all wrapped in Firestone Firehawk Indy 500 rubber. In front the rubber measures 265/35R18 and in the rear 325/30R19.

Once inside this Trans Am you will begin to see the many interior appointments, such as the Ridetech 304 stainless steel TigerCage. It is wrapped in matching Lipstick Red leather as is the modified factory dash and the Corbeau bucket seats by Chuck Hanna of Hot Rod Interiors. The modified dash is fitted with Dakota Digital Retrotech RTX gauges, Vintage Air A/C, and air registers. Mounted to the lower dash is an ididit column with a drilled three-spoke Lecarra leather-wrapped wheel. The custom-made interior door panels are fitted with LED lighting, Ridetech five-point belt system, and red Daytona weave carpeting are more interior appointments. The interior door releases are relocated to the custom center console while the hand formed speaker grilles cover the Rockford Fosgate speakers and New Relics operates the power windows.

Chris is no stranger to building hot rods and customs and has done so for the past 40 years, 25 of which has been full time. He’s built SEMA cars, Great 8 cars for Detroit, and many magazine cars. He is also recognized as an award-winning builder, having been inducted into the Darryl Starbird National Rod and Custom Hall of Fame and the KKOA Hall of Fame. We have to say that he has done it again with this ’78 Pontiac Firebird Trans Am.