Modern Rodding Tech
InTheGarageMedia.com
’32 Ford Three-Window Coupe
Lowering the Lid title
Lowering the Lid
PART 2: Chopping Your ’32 Ford Three-Window Coupe
By Tony Thacker Photography by THE AUTHOR
P

utting up a customer’s brand-new Brookville steel three-window Deuce body is always a daunting task, especially if you have never chopped a car before. Such was the dilemma of Evan Veazie of the Veazie Bros. hot rod shop in Pomona, California (the site of the old SO-CAL Speed Shop).

As we learned in part one, Evan shopped around and asked everybody he knew how to make his first cut, however, he ultimately digested all the good advice but went his own way, executing a simple-but-effective chop that is one of the cleanest cuts I have ever seen, and I’ve seen a few.

Instead of just slicing 2 inches out of the middle as most people would do, Evan carefully mapped out a plan to cut the roof in a step that allowed him to remove 2 inches and lower the roof until it aligned with the body. It was an amazingly smooth operation that took less than eight hours to complete. That’s the main chop, however, and did not include chopping the doors, moldings, and so on, all of which took considerably longer and will be covered in a part three. It did include the front posts that because of their inner structure are finicky.

The equipment needed to perform this operation is minimal; all you need is a cut-off wheel, a grinder, a skill saw, a welder, and some patience to see it through. A few extra hands were needed to lift the roof on and off but mostly it was a one-man operation that you could perform at home. If Evan can do it, you can do it.

You can see here that as the result of lots of outside advice Evan scratched a few lines in the Dykem before he settled on exactly where he was going to make his cuts.
1. You can see here that as the result of lots of outside advice Evan scratched a few lines in the Dykem before he settled on exactly where he was going to make his cuts.
Initially, Evan was going to remove a 2-inch slice as shown, however, he decided on a different route whereby the outtake would  be lower and follow the roof swage line.q
2. Initially, Evan was going to remove a 2-inch slice as shown, however, he decided on a different route whereby the outtake would be lower and follow the roof swage line.
Once Evan had made up his mind where the cut was coming, he used 1/4-inch blue tape to mark out his cut line. You can see where the curved cut is going to be.
3. Once Evan had made up his mind where the cut was coming, he used 1/4-inch blue tape to mark out his cut line. You can see where the curved cut is going to be.
Here’s the cut line at the back by the rear window. You can clearly see the step-up where the cut coincides with the straightest, vertical part of the window frame.
4. Here’s the cut line at the back by the rear window. You can clearly see the step-up where the cut coincides with the straightest, vertical part of the window frame.
Evan uses an air-powered cut-off wheel that you might not have but you could put one in a cordless drill or worse, use an angle grinder if that’s what you have. Or, pay a visit to your local Harbor Freight to gather the necessary metalworking tools.
5. Evan uses an air-powered cut-off wheel that you might not have but you could put one in a cordless drill or worse, use an angle grinder if that’s what you have. Or, pay a visit to your local Harbor Freight to gather the necessary metalworking tools.
Here, Evan has moved onto the vertical cut behind the doorjamb. Some people have said cut-off wheels contaminate the metal and they may but does it really matter?
6. Here, Evan has moved onto the vertical cut behind the doorjamb. Some people have said cut-off wheels contaminate the metal and they may but does it really matter?
The first cut is the deepest, well, it’s the first cut. Ignore all the scribed lines except the one at the bottom down near the roof-to-body beading.
7. The first cut is the deepest, well, it’s the first cut. Ignore all the scribed lines except the one at the bottom down near the roof-to-body beading.
Up front on the windshield posts a cut-off wheel was used to cut the outer skins but there’s strengthening structure inside the posts that needs to be cut with a skill saw.
8. Up front on the windshield posts a cut-off wheel was used to cut the outer skins but there’s strengthening structure inside the posts that needs to be cut with a skill saw.
Once the cut was complete it took four guys to lift the roof off the body, however, you could always tie the roof to the roof of your shop and roll the body and frame out from under.
9. Once the cut was complete it took four guys to lift the roof off the body, however, you could always tie the roof to the roof of your shop and roll the body and frame out from under.
Here you can clearly see where the cuts were made. Thankfully, the rear part of the body is single-skinned and not at all difficult to cut.
10. Here you can clearly see where the cuts were made. Thankfully, the rear part of the body is single-skinned and not at all difficult to cut.
Using the cut-off wheel, Evan cut 2 inches from the rear doorframe. Again, if you don’t have a cut-off wheel you could use some other tool, even a hacksaw if that’s what you have.
11. Using the cut-off wheel, Evan cut 2 inches from the rear doorframe. Again, if you don’t have a cut-off wheel you could use some other tool, even a hacksaw if that’s what you have.
Evan then went back and using the cut-off wheel carefully removed the 2 inches that will constitute the chop. It’s a different but clever way of chopping a top.
12. Evan then went back and using the cut-off wheel carefully removed the 2 inches that will constitute the chop. It’s a different but clever way of chopping a top.
Because of the internal strengthening structure a skill saw is needed to cut through the multiple layers. Remember to always work safe and wear safety glasses.
13. Because of the internal strengthening structure a skill saw is needed to cut through the multiple layers. Remember to always work safe and wear safety glasses.
A bird’s eye view of the inner structure of the front windshield posts. These took some rebuilding as Evan got into the assembly.
14. A bird’s eye view of the inner structure of the front windshield posts. These took some rebuilding as Evan got into the assembly.
Owner Bruce Forte ponders what he’s got himself into as Evan shapes the roof section that you can see clearly in the foreground. It drops right back onto the body.
15. Owner Bruce Forte ponders what he’s got himself into as Evan shapes the roof section that you can see clearly in the foreground. It drops right back onto the body.
With the roof just balanced on the body you can see how clean and simple this style of chop is with no splits in the roof at all. A 3-inch chop might be different though.
16. With the roof just balanced on the body you can see how clean and simple this style of chop is with no splits in the roof at all. A 3-inch chop might be different though.
Although he’d never chopped a top before Evan thought it through and came up with his own clean method to make the cut. Simple and effective.
17. Although he’d never chopped a top before Evan thought it through and came up with his own clean method to make the cut. Simple and effective.
From the rear you can see that there is some misalignment that is only to be expected but it’s pretty close and the window has a nice symmetrical shape.
18. From the rear you can see that there is some misalignment that is only to be expected but it’s pretty close and the window has a nice symmetrical shape.
From the front it’s the same story. The posts need a little jiggery pokery but nothing that you’d need a PhD for.
19. From the front it’s the same story. The posts need a little jiggery pokery but nothing that you’d need a PhD for.
As everything lined up better than expected, Evan began to tack the roof in place.  Tacks were every 1/2 inch or so.
20. As everything lined up better than expected, Evan began to tack the roof in place. Tacks were every 1/2 inch or so.
Obviously, some slicing and dicing was necessary to re-align the doorjamb but again nothing more than a saw cut to re-position.
21. Obviously, some slicing and dicing was necessary to re-align the doorjamb but again nothing more than a saw cut to re-position.
 Inside, the story is much the same, the roof was just gently pushed and pulled to align with the body and tacked into position with no unnecessary splitting.
22. Inside, the story is much the same, the roof was just gently pushed and pulled to align with the body and tacked into position with no unnecessary splitting.
 After careful hammer welding the joint, the worked area was ground smooth and you can hardly see the joint.
23. After careful hammer welding the joint, the worked area was ground smooth and you can hardly see the joint.
Because of their inner structure, the front posts need some work to rebuild and Evan basically fab’d up a structure and then covered it with the original skin.
24. Because of their inner structure, the front posts need some work to rebuild and Evan basically fab’d up a structure and then covered it with the original skin.
The outer skin was carefully cut and massaged to fit the hole. Note, this is still in process and some work is needed before it’s an acceptable fit.
25. The outer skin was carefully cut and massaged to fit the hole. Note, this is still in process and some work is needed before it’s an acceptable fit.
 Fabricator Greg Hirata acts as a porta power holding the roof in alignment with the posts as Evan tacks the pieces into position.
26. Fabricator Greg Hirata acts as a porta power holding the roof in alignment with the posts as Evan tacks the pieces into position.
Almost done. What’s now needed is to finish up the welding and make sure the doors and trim are cut to fit. One more part to go!
27. Almost done. What’s now needed is to finish up the welding and make sure the doors and trim are cut to fit. One more part to go!
Brookville Roadster
(937) 833-4605
brookvilleroadster.com
Veazie Brothers Fabrication
(909) 438-6632
Modern Rodding
VOLUME 3 • ISSUE 16 • 2022